Nitro Gas Shocks: Nitrogen Gas Charged Shock Absorbers
Tough Dog Nitrogen Gas shock absorbers have been designed with control and comfort in mind.
Nitro gas shocks are built with multi stage velocity sensitive valving to ensure the shock is capable of performing at any speed. As the shock moves faster to absorb small bumps in the road like corrugations, the valving in the shock responds to maintain the ride control characteristics. These shocks are perfectly suited to light and medium four wheel drives and vehicles with leaf sprung suspension.
- 35mm Internal bore and piston with twin tube design
- Low pressure nitrogen gas to eliminate fade for better performance and comfortable ride
- Double chrome-plated shaft
- High temperature, all weather fluid
- Custom designed for each application
- OEM or longer length shocks to suit standard or raised 4WDs for maximum articulation, comfort, safety & durability
- 2 Year/40,000km warranty (conditions apply)
Torsion Bars:
Tough Dog Performance 4WD Torsion Bars offer a spring rate that is approximately 30% higher than OEM bars.
This dynamic increase in spring rate eliminates hard bottoming out when travelling off road and gives better handling in street applications. They can be installed with a moderate pre-load to raise the vehicle for better clearance off road, or to revitalise the handling characteristics at the standard height. These performance-proven, easy-to-install bars are especially beneficial when oversize tyres or frontal accessories are installed. Regardless of the torsion bar used, or the accessories fitted, a minimum 60mm of suspension droop (down travel) must be maintained.
Optimise your 4WD’s ride & handling characteristics with quality torsion bars from ToughDog!
Leaf Springs:
Designed in Australia, Tough Dog leaf springs offer a spring pack for just about any application you might require. Our springs are a proven performer in any situation.
Tough Dog leaf springs are a truly progressive rate leaf spring. Each leaf is set slightly higher than the leaf above so there is contact along the whole length of each leaf. There are single stage and two stage springs available for different applications. Primary and secondary stage leaves ensure that the vehicle’s ride remains uncompromised. As the spring is compressed under load, the heavier second stage leaves come into play to prevent excessive sag & remove high stresses from the primary stage.
- Precision mandrel & die-formed
- Oil quenched, hardened & tempered for maximum life.
- Military wrap for safety
- Accurately heat-treated
- Manufactured from high grade spring steel
- Anti-friction pads in most applications
- Pre-stressed to maintain ride height
- Diamond cut ends
- Load rate tested
- 2 year/40,000km warranty
U-Bolts:
When U-bolts are tightened to secure the leaf pack in the vehicle from factory, the metal is stretched as a normal part of this process. It is important that U-bolts be replaced when a suspension system is changed, as a stretched U-bolt has lost its integral strength. The U-bolt will appear tight when re-used, but in fact it isn’t, this puts undue pressure on the centre bolts in the springs, causing them to move or snap which in turn allows the diff to move and the leaves to spread. Tough Dog U-bolts are manufactured using high tensile steel & are designed with the correct length of thread for larger, heavy duty leaf spring packs.
Urethane Bushes:
Leaf spring based suspension set ups generally have a bias leaning towards load carrying capability over ride quality. The design and composition of the shackle hanger and bushing material can make all the difference to your ride quality. This assembly is the spring’s first part to move in response to uneven terrain and bumps in the road. Tough Dog urethane is stronger than rubber components and has greater longevity and resistance to deterioration from chemical exposure. Urethane bushes respond well to greasing during operation and are created to retain flexibility for ride comfort. When required, steel tubes in the centre of the bush are hardened and chemically treated to resist corrosion. All of this will keep your leaf sprung vehicle in positive contact with the road surface and give you better tyre and suspension component life. Replacement urethane bushes are available for all Tough Dog leaf springs as well as for a range of other suspension bushing locations in vehicles. Tough Dog also have a range of coil spring spacers to assist in levelling and trimming live axle coil vehicles. Poured as a single piece urethane, Tough Dog spring spacers are available in various heights, depending on the vehicle and application.
"Kit Installation Charges - $300"